Gundam Australia Forum Sponsored By Hobby Link Japan - Go there NOW
July 06, 2020, 09:06:40 AM *
Welcome, Guest
Please login or register.

Login with username, password and session length
Advanced search  

News:

Ordering something from HLJ? Access the site through our banner! :)

Follow Us On -
Fury's Schemer App
SAZABI VER KA!!!!
HLJ.com Ad

Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.

Messages - dj898

Pages: 1 ... 5 6 [7]
91
Officer's Bulletin / Re: Gunpla with Attitude
« on: January 10, 2011, 08:18:54 PM »
Yep!
Keep em coming

92
Officer's Bulletin / Gunpla with Attitude
« on: January 10, 2011, 07:06:05 PM »


 Vs



Vs



Vs



Vs



if you have one with the attitude please post as well!  ;D

93
Engineering Corps / Re: Pla Plate and General Modding help
« on: January 10, 2011, 08:25:00 AM »
no.

you start with this:


and after done with heat press method you got this:


when put together this looks like this - much better no?

94
Arms Dealers / Re: Hobby Co
« on: January 01, 2011, 09:56:21 PM »
went to city on Friday since everyone was leaving work after lunch.
unfortunatrly there were none that I was after...
still not a bad trip as I picked up old issue of dengeki with 1/144 hanger kit plus Tony Takezaki III - bloody funny if you ask me ^ ^

would love to eat at ichibanboshi but had to leave within an hour so no time... ;(

95
Engineering Corps / Re: Tools Of The Trade (what's in your tool box)
« on: January 01, 2011, 09:51:20 PM »
Here's what I normally use for fitting stage.


and for the rest I've written about the same topic on my blog.
Link

96
Sortie Analysis / Re: Gundam Manga
« on: December 31, 2010, 11:04:55 AM »
two of my fav are these guys ^ ^


*ganpra kyoushien


*pramo kyoshiro

97
Engineering Corps / Re: Pla Plate and General Modding help
« on: December 31, 2010, 10:33:16 AM »
nope.

get a cheese tray you get from Tasty Cheese or something from supermarket
also get the small flat candle from candle shop

get a part where you want the plus mould using the cheese tray and once it gets heated enough on the candle press it on the part and hold still for couple seconds

trim the excess and etc.

98
Engineering Corps / Re: spray cans
« on: December 29, 2010, 10:44:50 PM »
one advice

don't go cheap
you are going to waste a lot of pant for a kit and that's the point
when you start to think the total cost of cans almost equal to the decent air brush kit then it's time to upgrade

99
Engineering Corps / Re: Nu Gundam Proportions
« on: December 29, 2010, 11:12:36 AM »
the point of topic does have merit

I myself had somewhat similar experience with 1/100 GM Spartan conversion kit
As I wasn't too keen on the whole conversion I ended up going hard route and fabricate a lot of conversion pieces from existing MG kit parts - and at the end still didn't like ;(

basically I was trying to make the ako conversion into reckless GM Spartan profile... OTL

100
Sortie Analysis / Re: Mokei Senshi Gunpla Builders Beginning G
« on: December 29, 2010, 11:07:59 AM »
I agree but in the last part of the episode 3, it's mentioned maestro...
no that guy with glass is maestro but does our boy in the same class?

but then when watching the episode 2 he does have amazing brush skill - no masking what so ever and finishing off in one stroke what would take hours for me to complete using masking tape, etc. ;p

101
Sortie Analysis / Re: Mokei Senshi Gunpla Builders Beginning G
« on: December 29, 2010, 10:16:12 AM »
over the x-mas break saw all three episodes.

come on in just a year from newbie to maestro ?
gimme break... -__-;

the gunpla battle idea is neat though it's nothing new as same concept was used in Pramo Kyoshiro(?) manga

102
General Discussion / Re: Gundam U.C
« on: December 29, 2010, 10:11:22 AM »
for those short of time just watching MS Gundam Movies plus Zeta and followed by Char's Counter Attack should be enough.

though 08th MS Team is quite good it broke way too many established plot lines and ZZ is best to be buried deep in the sand and think of it never happened...

0080, 0083, and egloos are best when you crave for some more...

103
Engineering Corps / Re: Pla Plate and General Modding help
« on: December 28, 2010, 07:53:12 PM »
1. how to pla plate curved surfaces while minimising stress on the pla plate:
depends on the thickness but it's thin enough you can alkways use heat press method

2. What kinds of tools are needed for working on pla plates and metal:
what you use for your gunpla can be used ith pla plates
for metal you will want separate set as working with metal will dull the tool real quick

104
Friendly Fire / Re: dj898.egloss.com
« on: December 28, 2010, 07:33:19 PM »
thanks for the kind words mate ^ ^

btw it's dj898.egloos.com

Pages: 1 ... 5 6 [7]


japantoys.com.au banner ad

HLJ.com Ad

Advertise on GAF